Brayton gas turbine cycle has two stages of compression

Assignment Help Mechanical Engineering
Reference no: EM13488826

A Brayton gas turbine cycle has two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and turbine is 3. The air enters each stage of  the compressor at 300K and each stage of the turbine at 1200K. If the efficiency of each
compressor is 80% and each turbine is 85%
Determine: using variable specific heat method for:
Case 1) no regenerator
a) The back work ratio
b) The thermal efficiency
Case 2) a regenerator with 75% effectiveness
a) The back work ratio
b) The thermal efficiency

Reference no: EM13488826

Questions Cloud

Explain what will be the final temperature of the system : If a 1.00 cm^3 solid cube of alumina ceramic initially at 300 C is placed in 50 ml of H2O initially at 25C in a closed, insulated container: (a) what will be the final temperature of the system when thermal equilibrium is attained.
Discuss if tony has any tax implication : Students should be able to identify and apply legislation and case law to the issues identified as well as demonstrates the ability to analyses the issues fully and discusses the application of taxation principles.
How much chemical energy is used : A 47% efficient device uses chemical energy to generate 550J of electric energy. How much chemical energy is used
Evaluate the mass of cuso4*h2o : Calculate the mass of CuSO4*H2O needed to prepare 3.0 g of [Cu(NH3)4]SO4*H2O, assuming a 90% yield.
Brayton gas turbine cycle has two stages of compression : A Brayton gas turbine cycle has two stages of compression and two stages of expansion. The pressure ratio across each stage of the compressor and turbine is 3. The air enters each stage of  the compressor at 300K and each stage of the turbine at 1..
Explain what is rate of heat loss through : If a single pane glass window on a house has an area of 0.5 m^2 and is 3mm thick, what is rate of heat loss through this window on a cold winter day when the inside surface of the glass is 15?C and the outside surface is 5C
Determine the precession rate : A certain gyroscope consists of a uniform disk with a 52 cm radius mounted at the center of an axle that is 12 cm long and of negligible mass. what is the precession rate
How much will you have saved for retirement : You are 25 years old and decide to start saving for your retirement. You plan to save $5000 at the end of each year (so the first deposit will be one year from now), and will make the lastdeposit when you retire at age 65. Suppose you earn 8% per yea..
Explain the monomers below to create one repeat : Kevlar is a strong synthetic fiber used in bullet proof vests and body armor. Kevlar is made by the condensation reaction between 1,4-phenylene-diamine and terephthaloyl chloride. Modify the monomers below to create one repeat unit of the polymer.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  What is the maximum amount of work

No heat interactions with the environment are allowed. You do not need to describe the details of the process that produces the maximum work, but you do need to describe the final state of the blocks fully.

  Explain what is the basic design load rating

Design life is 9630 hours, rotating at 250 rpm, load of 880 lbs, what is the basic design load rating (assuming no axial loads)?

  Module fea - finite element analysisnbspquestion 2 method

module fea - finite element analysisnbspquestion 2 method to assess the value of your analysis outputnbspa what is the

  A bullet of mass 006 kg is fired horizontally into a wooden

a bullet of mass 0.06 kg is fired horizontally into a wooden block of mass 0.10 kg. the wooden block is suspended from

  A standardized procedure is expected to produce washers

a standardized procedure is expected to produce washers with very small deviation in their thicknesses. suppose that 10

  Determine the tensions at the cables

the suspended load exerts a force F=600 lb at A, and the weight of the bar OA is negligible. Determine the tensions at the cables and the reactions at the ball and socket support O

  A 75-lb stoplight is suspended between two poles as shown

a 75-lb stoplight is suspended between two poles as shown in fignbspp3-27. neglect the weight of the flexible cables

  What steel specification suitable for structural application

Find the stress in both members shown below and what steel specifications (types of steel) are suitable for structural applications?

  Determine the speed of the block at the instant

If the truck starts from rest when xD is zero, and moves forward with a constant acceleration of aD = 5 m/s2, determine the speed of the block at the instant xD = 3 m.

  Determine the radius of curvature of the trajectory

Coal is discharged from the tailgate of a dump truck with an initial velocity vA = 2 m/s A 50°. Determine the radius of curvature of the trajectory described by the coal.

  Determine the smallest horizontal force requirednbspto lift

determine the smallest horizontal force required to lift the 260- crate. the coefficient of static friction at all

  Derive an expression for the net work transfer

(a) derive an expression for the net work transfer for the cycle. Prove that for a Stirling Cycle, the net work transfer is always from the system to the surroundings.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd