Ball is dropped inside an evacuated tube

Assignment Help Mechanical Engineering
Reference no: EM13709778

A ball is dropped inside an evacuated tube so that there is no aerodynamic drag acting on the ball. At one point it is at a height of 2.5 m and is dropping at a speed of 1.0 m/s. What will be the height of the ball when its speed is 5.0 m/s? Take g= 9.81 m/s2

Reference no: EM13709778

Questions Cloud

Derive the expression for a simple spring mass system : Derive the expression for a simple spring mass system equation and its response. Plot the response for 3 different values of k, (k=1, k=10, k=100) assume mass M= 1, what are the natural frequencies in rad/sec and Hz for each case. Explain the differe..
Find the speed of transverse waves in the wire : A variable-length air column is placed just below a vibrating wire that is fixed at the both ends. Find the speed of transverse waves in the wire
Find the total force resisting the motion of the block : A 25-N block slides down a plane inclined at 21.2 degrees to the horizontal with constant velocity. Find the total force resisting the motion of the block
Car accelerates from rest along a straight section of road : A car accelerates from rest along a straight section of road. It starts at position s = 150 m and reaches a speed of 20 m/s at position s = 200 m. It is proposed that this acceleration, a, can be modelled as being a function of position, s, in the fo..
Ball is dropped inside an evacuated tube : A ball is dropped inside an evacuated tube so that there is no aerodynamic drag acting on the ball. At one point it is at a height of 2.5 m and is dropping at a speed of 1.0 m/s. What will be the height of the ball when its speed is 5.0 m/s? Take g= ..
How would you attempt to maximize patient satisfaction : How would community-based participatory research principles be reflected in the development of an intervention to promote the utilization of preventive health services by African-American men?
Obtain the minimum area plates of this capacitor can have : A parallel-plate capacitor is to be constructed by using, as a dielectric, rubber with a dielectric constant of 3.20 and a dielectric strength of 25.0MV/m. What is the minimum area the plates of this capacitor can have
Look for postings of technology-driven mergers : Use your favorite search engine on the Internet and look for postings of technology-driven mergers and acquisitions. What are the reasons given for the mergers and acquisitions? What is described as coming from each of the organizations? Are t..
Determine the acceleration of the sphere : A point charge q1=15.00 µC is held fixed in space. From a horizontal distance of 7.00cm, a small sphere with mass 4.00 × 103 kg and charge q2=+2.00 µC is fired toward the fixed charge with an initial speed of 35.0 m/s. What is the acceleration of the..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Saturated ammonia vapor leaves an evaporator at 10 f and 05

saturated ammonia vapor leaves an evaporator at 10 f and 0.5 lbms. the velocity must be less than 15 fts. what is the

  Determine enthalpy change for process and final fluid phase

Refrigerant - 12 as saturated vapor at 0.5 MPa is isentropically compressed by a compressor in a refrigeration plant to 0.9 MPa. Determine the enthalpy change for the process and the final fluid phase.

  A 075m3 tank contains nitrogen at 150kpa and 40degc 20 kg

a 0.75m3 tank contains nitrogen at 150kpa and 40degc. 2.0 kg of oxygen are added to the tank. what is the final

  Ethane gas is burned in a steady-flow process with 30

ethane gas is burned in a steady-flow process with 30 excess air both of which enter separately at 25 0 c and 1 atm.

  B determine the maximum velocity attained by the collar a

the system is released from rest in the position shown. the masses of the collar a and the box b are ma 90 kg and mb

  A gate having a cross section as shown an opening 5 ft

a gate having a cross section as shown an opening 5 ft wide and 4ft high. the weights 400 lbs and its center of gravity

  An ideal gas at 20 bar and 400 celcius is being fed into an

an ideal gas at 20 bar and 400 celcius is being fed into an adiabatic turbine to generate electricity at a rate of 278

  What is the work done on or by the steam

A piston-cylinder contains 0.1 kg of superheated steam at 180 ¯ C and 5.0 bars. The piston is frictionless and freely floating. Heat is added until the final volume is twice the initial volume.

  Determine the rate of heat transfer kw to the high

a system that operates in a reversible cycle receives energy by heat transfer from a 24.8oc reservoir at a rate of 25.5

  What diameter should the hovercraft deck be to operate at

1. a circular hovercraft is to levitate at a gap height of 2.5 mm after picking up a payload. the hovercraft has a

  Determine whether erosion will take place if the maximiun

an earthen channel n0.03 has a bed width of 5.0 m a water depth h 1.5 m a 45deg side slope and a channel slope of

  The plate is subjected to an axial force of 75 kn the

the a-36 steel plate has a thickness of 12 mm and other dimensions. r30mm p60mm ab200mm bc800mm cd200 width120mm. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd