At what temperature change delta t does the wire go slack

Assignment Help Civil Engineering
Reference no: EM13296822

a brass wire of diameter d=1/6 in is stretched between rigid supports with an initial tension T of 37lb. assume the coefficient of thermal expansion is 10.6X10^-6 / F and the modulus of elasticity is 15X10^6 psi.

at what temperature change Delta T does the wire go slack?

Reference no: EM13296822

Questions Cloud

What do you think are the effects of such a ruling : In late February, 2005, the U.S. Supreme Court ruled that the death penalty is unconstitutionally cruel when applied to people who committed a felony deserving of the death penalty according to state law before they reached age 18
Which car had the greater velocity before the collision : Two cars of equal mass collide at right angles to each other in an intersection. Which car had the greater velocity before the collision
How fast could the insect be moving : A visual inspection of an insect with mass 0.4mg (milligrams) suggest that its uncertainty in postion is 0.5um, How fast could the insect be moving
Explain order of decreasing net dipole moment : Which of the following pairs of molecules is listed in order of decreasing net dipole moment (from more polar molecule to less polar molecule)
At what temperature change delta t does the wire go slack : a brass wire of diameter d=1/6 in is stretched between rigid supports with an initial tension T of 37lb. assume the coefficient of thermal expansion is 10.6X10^-6 / F and the modulus of elasticity is 15X10^6 psi.
Determine what is the total elongation of the pipe : a prismatic bar AB of length L, cross section A, modulus of elasticity E, and weight W hangs vertical under its own weight. if the bar is a riser pipe hanging from a drill rig at sea, what is the total elongation of the pipe
Determine what is the max length of the slotted region : a rectangular bar of length l has a slot in the middle half of its length. the bar has width b, thickness t, and modulus of elasticity E. the slot has a width b/4. the stress in the middle region is 24000 psi, the length is 30 in, andthe modulus o..
Define the following balanced chemical equation : Given the following balanced chemical equation, if 345 g of I2 are formed, how many g of Cl2 had to react? 2 FeI2 + 3 Cl2 ? 2 FeCl3 + 2 I2
Determine what is the maximum water hammer pressure : 0.5 m-diameter concrete pipe (5.0 cm rigid wall thickness with rigid pipe walls) carries water 600m before discharging into another reservoir. The surface elevation of the downstream reservoir is 55 m lower than the supply reservoir.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Concentration of tracer in the reactor

What is the concentration of tracer in the reactor 1 h after tracer addition is terminated? The reactor had an initial concentration of tracer of 1.0 mg/L when tracer addition commenced.

  Explain cbr method of pavement design

Explain CBR method of pavement design with one example.

  Replace the two couples with a single equivalent couple

The two shafts in a speed-reducer unit are subjected to couples of magnitude M1 = 18 N · m and M2 = 7.5 N · m, respectively. Replace the two couples with a single equivalent couple, specifying its magnitude and the direction of its axis.

  Plot the magnitude of the force exerted on the gate

Plot the magnitude of the force exerted on the gate by the brace as a function of the angle of the gate, , for . Assume the weight of the gate is negligible.

  Determine the void content

If the dry-rodded unit weight of an aggregate is 105 lb/ft3 (1680 kg/m3) and its specific gravity is 2.65, determine the void content.

  Estimate the wet density

A sample of natural glacial till was taken from below the groundwater table. The water content was found to be 52%. Estimate the wet density,dry density,buoyant density,porosity,and void ratio. Clearly state any necessary assumptions.

  Calculate q-w change in u and h for each processes

Cooling at constant pressure followed by heating at constant volume. Calculate Q, W, change in U, and change in H for each of these processes, and sketch the paths of all processes on a single PV diagram.

  What are the coordinates of the point

An agronomist wants to measure the rainfall at the centroid of a plowed field between two roads. What are the coordinates of the point where the rain gauge should be placed?

  Ratio of the magnitude in uniform electric field

What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.

  Compute difference in the weights of dry gravel in a 10 ton

A stockpile of gravel that has a water content of 6% is rained on so that its water content increases to 9%. Compute the difference in the weights of dry gravel in a 10 ton truckload taken from the pile before and after the rain.

  Determine the velocity of slider block

Knowing that at t= 3s slider block C has moved 57 mm to the right, Determine the velocity of slider block C at t=0, (b) the acceleration of A and C, (c) the change in position of block A after 5s.

  Determine the flow rate of the oil

Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd