At what rate must 15c makeup water be provided

Assignment Help Civil Engineering
Reference no: EM13539090

A 600 MW power plant has an efficiency of 36 percent with 15 percent of the waste heat being released to the atmosphere as stack heat and the other 85 percent taken away in the cooling water. Instead of drawing water from a river, heating it, and returning it to the river, this plant uses an evaporative cooling tower wherein heat is released to the atmoshphere as cooling water is vaporized.

At what rate must 15C makeup water be provided from the river to offset the water lost in the cooling tower?

Reference no: EM13539090

Questions Cloud

Determine the max allowable stress : Given an aluminum simply supported beam with overhang, determine the applied load at the free end with a max deflection of 1”. b= 1”
Draw the shear and moment diagrams for the girder : The concrete girder supports the two column loads. If the soil pressure under the girder is assumed to be uniform, determine its intensity w and the placement d of the column at B. Draw the shear and moment diagrams for the girder.
How much would her first deposit be in actual dollars : On her 23 birthday, and engineer decides to start saving toward building ip a retirement fund that pays 8% interest compounded quarterly (market interest rate) She feels that 600,000 worth of purchasing power in today's dollars will be adequate
Determine what force must be applied to the plunger : A hypodermic syringe is attached to a needle that has an internal radius of 0.301 mm and a length of 3.01 cm. What force must be applied to the plunger
At what rate must 15c makeup water be provided : A 600 MW power plant has an efficiency of 36 percent with 15 percent of the waste heat being released to the atmosphere as stack heat and the other 85 percent taken away in the cooling water. Instead of drawing water from a river, heating it, and ret..
Determine the location of the centroid relative : Design a 2:1 rectangular duct and fan system to pull 40000 scfm of air carrying a medium-density dust through an FCD (Final Control Device) with a ?P of 6.0 in. H2O. Assume the duct system must extend 120-feet and has four 90° elbows.
Calculate the dispersion of the slab : A light beam containing red and violet wavelengths is incident on a slab of quartz at an angle of incidence of 50.7°. Find the dispersion of the slab
Calculate how much energy was dissipated by friction : A 16 kg girl slides down a playground slide that is 2.8 m high. When she reaches the bottom of the slide, her speed is 1.3 m/s. How much energy was dissipated by friction
How far does the platform float above the water surface : A floating platform is supported at each corner by a hollow sealed cylinder 1 m in diameter, the platform itself weighs 25kN in air and each cylinder weighs 1.2kN per meter of length.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find corresponding racing speed and drag on the car

A one tenth scale model of a soap box derby car is tested in a wind tunnel. The air speed in the wind tunnel is 70m/s, the air drag on the model car is 240 N, and the air temperature and pressure are identical to those expected

  Determine how far upstream of the section would be expected

The slope of the channel So=.15% and the Manning n=.038. Estimate the depth y2=100m upstream of a section where the flow depth y1=2.2m Using a) the direct integration method and b) the standard step method.

  What percent of the particles does the settling tank capture

The setting velocity of a particle is 0.002 m/s and the overflow rate of a settling tank is 0.008 m/s. (a) what percent of the particles does the settling tank capture. If the particles are flocculated so that thie rsettling rate is 0.05 m/s

  Do any of the three wells exceed the 44 ppm level

Nitrate concentrations are often recorded in units of NO3--N/L to be compared with other nitrogen constituents. Near three rural wells nitrate concentrations were reported as 0.25 mg

  Determine angle of internal friction for effective stress

A consolidated-undrained type of test is performed. The sample fails (shears) when the total all-around confirming pressure is 45 kpa and the total axial pressure is 97 kpa.

  Determine the distance the orbiter travels from the time t

A 230,000-lb space shuttle orbiter touches down at about 220 miles per hour (mph). At 200 mph, its drag parachute is deploys. The wheel brakes are applied at 100 mph until wheel sotp and the drag parachute is jettisoned from the orbiter at 35 mph.

  Related geotechnical engineering

This material is related Geotechnical Engineering, please only answer if you are certain and sure of your answer. An undisturbed soil sample has a dry unit weight of 112 pcf with a specific gravity of solids equals to 2.68.

  Design a suitable pavement consisting of a granular subbase

if the subgrade has a resilient modulus of 103,500kN/m2, design a suitable pavement consisting of a granular subbase with a layer of coefficient of 0.13, a granular base layer with a layer coefficient of 0.14, and an asphalt concrete surface with ..

  What is peak q if a 4 per hr rain falls for 10 minutes

A 300 acre parking lot has a runoff coefficient of 0.8 and a time of concentration of 40 minutes. Using the rational method (Q=CIA), what is peak Q if a 4"/hr rain falls for 10 minutes

  What is the 2-4-6-trichlorophenol concentration in ppm

A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm Assume the temperature of the system is 20 degrees C.

  What percent increase in shear force would be experience

What percent increase in shear force would be experience on the flat sides of a 40 ft long truck trailer as the truck speed increases from 65 mph to 75 mph. Kinematic viscosity of the air is 1.6x10^4 ft^2/s.

  Compute radius of second curve stationing of the prc

The distance from the point of intersection of the tangents to the PI of the second curve is 100m while the stationing of the PI of the first curve is 10+432.24.If the radius of the curveis 285.40 m,

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd