Apply the newton-raphson method to the function fx tanhx2-9

Assignment Help Mechanical Engineering
Reference no: EM13614631

(a) Apply the Newton-Raphson method to the function f(x)= tanh(x^2-9) to evaluate its known real root at x=3. Use an initial guess of x0=3.2 and take a minimum of four iterations. (b) Did the method exhibit convergence onto its real root? Sketch the plot with the results for each iteration shown.

Reference no: EM13614631

Questions Cloud

Use your calculated z score along with the z table to find : a beer distributer believes that the amount of beer in a 12 ounce can of beer has a normal distribution with a mean of
Kinetic and potential energy effects can be neglected : water vapor at 5 bar. 320 degree c enters a turbine operating at steady state with a mass flow rate of 1.5 kgs and
Now use the calculate z score along with the z table to : the turkeys found in a county in southern ohio have an average weight of 15.6 pounds with a standard deviation of 4.0
Use the information above along with the z table to find : according to thepoultrysite.com the weights of broilers are approximately normally distributed with a mean of 1387
Apply the newton-raphson method to the function fx tanhx2-9 : a apply the newton-raphson method to the function fx tanhx2-9 to evaluate its known real root at x3. use an initial
Wat is the heat rejection for the condenser in btuh if : consider a small simple rankine power cycle which produces 600kw power from an electric generator with an efficiency of
Use the two calculated z scores along with the z table to : a company fills bags with fertilizer for retail sale. the weights of the bags of fertilizer have a normal distribution
Determine the final volume m3 of the water in the tank : initially an insulated rigid tank contains 3.73 kg of water at 240oc and 1 mpa. a heater in the wall of the tank
The beam ab is subjected to the uniformly distributed load : the beam ab is subjected to the uniformly distributed load shown and to two unknown forces p and q. knowing that it has

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine a the enthalpy of r-134a at the exit b the

r-134a is throttled from 1200kpa and 40oc to 200kpa. it is known that heat of 5kjkg is lost from r-134a to the

  Question 1 figure shows a pneumatic circuit diagram used

question 1. figure shows a pneumatic circuit diagram used for air supply and exhaust in an automatic control system.a

  What is thermal energy storage how does it differ from

what is thermal energy storage? how does it differ from thermal energy generation? what role do the terms play in a

  A hot dog can be considered to be a cylinder 12 cm long and

a hot dog can be considered to be a cylinder 12 cm long and 2 cm in diameter whose properties are rho 980 kgm3 cp 3.9

  Calculate the efficiency if a reheat loop was added at such

consider a steam plant operating on a rankine cycle with two open feed water heaters as shown in the figure. steam

  Determine the minimum coefficient of static friction

Determine the minimum coefficient of static friction between the crate and the truck so that the crate does not slide relative to the truck.

  A cylindrical wheel billet 1ft in diameter and 3ft long

a cylindrical wheel billet 1ft. in diameter and 3ft. long initially at 1000 f is quenched in oil. assume that the

  Plot contours of u-velocity and v-velocity

The velocity profiles at locations x=0.1, 0.30 and 0.5. Plot contours of u-velocity and v-velocity. How many iterations did it take to get your solution?

  What is the efficiency of the turbine-generator

A small hydroelectric power plant produces electrical power at a rate of 30 kW. The plant utilizes a stream of water that drops 40 m from a lake to the turbine and flows at a rate of 100 kg/s. What is the efficiency of the turbine-generator?

  Compute the lift l and drag d experienced by the aircraft

the 30 mg aircraft is climbing at the angle theta15 with a thrust t of 180 kn. at the instant shown its speed is 300

  The lower plate moves at a constant velocity v while the

a fluid is held between a lower place of temperature t1 and an upper place of temperature t2 the distance between the

  1 consider the diagram below where a pump is used to draw

1 consider the diagram below where a pump is used to draw water from a lake to feed an irrigation system.a which of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd