An ideal single reheat cycle uses a turbine inlet conditions

Assignment Help Mechanical Engineering
Reference no: EM13701086

An ideal single reheat cycle uses a turbine inlet conditions of 2500 psia and 1000F and a reheat temperature of 1000F with a reheat pressure ration of P2/P1 = 0.2 and a steam mass flow rate of Ms = 2*10^6 lbm/hr. The condenser operates at a pressure of 1 psia.

Find:

a) the power output, Wnet, in MW

b) the thermal efficiency, nth

Reference no: EM13701086

Questions Cloud

Temperature inside the cylinder remains constant : A mass of 1.5 kg of air at 120 kpa and 24 degrees C is contained in a gas-tight, frictionless piston-cylinder device. The air is now compressed to a final pressure of 600 kPa. During the process, heat is transferred from the air such that the tempera..
What is the power supplied to the cart : A 2 cm horizontal jet of water with a velocity of 15 m/s is spraying onto a vertical plate attached to a cart moving opposite the direction of the water jet at 8 m/s. Determine the force required to keep the cart moving at a constant velocity.
What is the exit air speed : Air enters a machine at 373 C with a speed of 200 m/s and leaves it at 293 C. If the flow is adiabatic, and the work output by machine is 105 Nm /kg, what is the exit air speed? What is the exit air speed when machine is delivering no work?
The pressure drop per unit length through the crack : A dam with water on one side has a 0.01 inch crack 10 feet below the surface of water. The length of the crack is 5 ft, and the thickness of the dam at that location is 3 ft. The water temperature is 50 degrees F. determine the following: The pressur..
An ideal single reheat cycle uses a turbine inlet conditions : An ideal single reheat cycle uses a turbine inlet conditions of 2500 psia and 1000F and a reheat temperature of 1000F with a reheat pressure ration of P2/P1 = 0.2 and a steam mass flow rate of Ms = 2*10^6 lbm/hr. The condenser operates at a pressure ..
A simple ideal ranking cycle has a power output : A simple ideal ranking cycle has a power output of 660 MW, a turbine inlet condition of T1=1000F, P1=1800 psia and a condenser operating pressure of P2=1.5 psia.
What is poisson ratio and shear modulus of this material : A 1 foot long cylindrical rod with a diameter of 0.25 inch is subjected to a tensile load of 1,500 lbs. Suppose the rod was elongated 0.01 inch under this load, what is the stress and strain created by the load? What is the Young’s Modulus of the mat..
What is the specific volume of the gas before the turbine : Air expands in an air turbine from a pressure of 50 psia and a temperature of 600°F to an exhaust pressure of 20 psia. Assume the process is reversible and adiabatic with negligible changes in kinetic and potential energy.
What is the specific heat capacity of this material : When a total amount of 125,000 joules of heat is transferred to a piece of 5 kg alloy, its temperature changes from 25 C to 60C, what is the specific heat capacity of this material?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Hot water is pumped through a plate heat exchanger the hot

hot water is pumped through a plate heat exchanger. the hot water side of the heat exchanger consists of 16 plates of

  Consider five kilograms of water at 10degc and 75 quality

consider five kilograms of water at 10degc and 75 quality in a closed container. the water is compressed isentropically

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  Determine the sum of the moments of the three weights

The 160-N weights of the arms AB and BC of the robotic manipulator act at their midpoints. Determine the sum of the moments of the three weights about A.

  Oil enters a counterflow heat exchanger at 450k with a mass

oil enters a counterflow heat exchanger at 450k with a mass flow rate of 10 kgs and exits at 350k. a seperate stream of

  Now take the gas in the cylinder alone as your system find

consider air in a piston-cylinder assembly. initially the air is at p1 2bars and t1 600k . the air is compressed

  What delta v was required

A satellite changes its orbit inclined 66 degrees at 260.0 km altitude to a polar orbit at the same altitude. What Delta V was required?

  T outlet is discharging water to the atmosphere

water flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3s. now a diffuser with an outlet diameter of 20

  A machinist is making engine parts with axle diameter of 07

a machinist is making engine parts with axle diameter of 0.7 inch. a random sample of 15 parts shows mean diameter

  Water is the working fluid in an ideal rankine cycle steam

water is the working fluid in an ideal rankine cycle. steam enters the turbine at 1400 lbfin2. the net power output of

  Knowing the ball takes 3 s to reach the borrom of the lake

a ball is dropped from a boat so that it strikes the surface of a lake with a speed of 16.5fts. while in the water the

  The membrane is broken and the air comes into a uniform

a tank has two rooms separated by a membrane. room a has 1kg of air and a volume of 0.5 m3 room b has 0.75 m3 of air

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd