User Account

All Pages

An airplane flying at a speed of 180 mph at an altitude of

Assignment Help Mechanical Engineering
Reference no: EM13345479

An airplane flying at a speed of 180 mph at an altitude of 40ft drops a large package at point A. The package has a parachute which deploys at B and allows the package to descend at a rate of 6 feet per second. The total time it takes to fall is 37 seconds. Find the horizontal lead to hit the target.

Reference no: EM13345479

Questions Cloud

If 1000 ml of no at stp reacts with 4000 ml of o2 at stp : the oxidation of nitric oxide to nitrogen dioxide is2nog o2g -gt 2no2gif 100.0 ml of no at stp reacts with 400.0 ml of
A paperclip is made of wire 125mm in diameter if the : a paperclip is made of wire 1.25mm in diameter. if the original material from which the wire is made nbspwas 15mm in
An electric oven operates at 120v if its power rating is : an electric oven operates at 120v. if its power rating is 0.6kw what amount of current does it draw and how much
A certain cross section lies in the x-y plane if 3x1020 : a certain cross section lies in the x-y plane. if 3x1020 electrons go through the cross section in the z-direction in
An airplane flying at a speed of 180 mph at an altitude of : an airplane flying at a speed of 180 mph at an altitude of 40ft drops a large package at point a. the package has a
Nicotine a component of tobacco is composed of c h and n a : nicotine a component of tobacco is composed of c h and n. a 12.075 mg sample of nicotine was combusted producing 32.757
Write a matlab function fcosine which will generate the : basic signals 1.generate and plot using matlabs stem command the sequence xn 0.95n cos?20 n for 0 le n le 63. note
Converting liquid water to solid ice releases 144 kcalmol : converting liquid water to solid ice releases 1.44 kcalmol.awhat is the sign of delta h for this process?bhow many
Calculate the equilibrium partial pressure of 2brcl : a reaction mixture initially contains a br2 partial pressure of 765 torr and a cl2 partial pressure of 730 torr at 150

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the compression ratio

determine (a) the compression ratio, (b) the cycle efficiency, (c) exhaust temperature, and (d) mean effective pressure (kPa). Draw (e) a P-v diagram and (f) a T-s diagram

  Steady state thermal analysis

Steady State Thermal analysis can be use to simulate and obtain results to support the design optimization / objectives

  How the lubricants reduce the friction

How the lubricants reduce the friction and wear characteristics of the parts in contact?

  What is the total current

A 60 ohm, 40 ohm, and 20 ohm resistor are each connected in parallel across a 120VAC source. What is the total current.

  A 02-cm-thick 10-cm-high and 15-cm-long circuit board

a 0.2-cm-thick 10-cm-high and 15-cm-long circuit board houses electronic components on one side that dissipate a total

  What is the semi-major axis of the orbit

A satellite is in Earth orbit with an altitude at perigee of 555.0 km and an altitude at apogee of 1200.0 km. a. What is the semi-major axis of the orbit? b. What is the eccentricity? c. If the true anomaly is 160 degrees, what is the satellite's ..

  A weight attached to a spring of stiffness 525nm has a

a weight attached to a spring of stiffness 525nm has a viscous damping device. when the weight is displaced and

  Determine the magnitude of the resultant force acting at a

The roof is supported by cables. If the cables exert FAB = 100N and FAC = 120N on the wall hook at A, determine the magnitude of the resultant force acting at A.

  Find the new optimal solution

Find the new optimal solution of the LPP if the availability of the second constraint

  Compute the steady-state creep rate

If it is known that the value of the stress exponent n for this alloy is 8.2, compute the steady-state creep rate at 1300 K and a stress level of 89 MPa.

  Determine the expressions for the principal stresses

A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.

  Evaluate the work required and the heat transfer

Kinetic and potential energy effects can be ignored. Evaluate the work required and the heat transfer, each in kW.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd