Air undergoes polytrophic process in piston cyllendar

Assignment Help Mechanical Engineering
Reference no: EM13717721

Air undergoes a polytrophic process in a piston cyllendar assembly from P1=1 atm, T1=70 degrees F, P2=5 atm. Employing ideal gas model with constant specific heats at 80 degrees F determine the work and heat transfer per unit mass in Btu/ibm if n=1.3 and n= specific heat ratio (k)

Reference no: EM13717721

Questions Cloud

Estimate the jet velocity relative to the airplane : The GE J-79 turbo jet produces a thrust of 10,000lbs at sea level. The inlet diameter is 3.19 ft. If an airplane equipped with the J79 is flying at standard sea level with a velocity of 1,000 ft/sec, estimate the jet velocity relative to the airplane..
Heat is added until the pressure doubles : Water is in a 0.05 m^3 piston-cylinder assembly at 1 MPa, 220 C and the piston is resting on stops. Heat is added until the pressure doubles. At this point the piston movies until the volume increases by 50%.
Write a balanced net ionic equation for acid-base reaction : Write a balanced net ionic equation for the acid-base reaction that takes place between aqueous potassium hydroxide and hydrochloric acid
What may happen to a large container of calcium hypochlorite : What may happen to a large (i.e., 30-50lb) container of trichloro-s-triazinetrione, or calcium hypochlorite, if it is left to sit in the water and muck remaining in a building after firefighting efforts have ended, but clean-up will not begin for ..
Air undergoes polytrophic process in piston cyllendar : Air undergoes a polytrophic process in a piston cyllendar assembly from P1=1 atm, T1=70 degrees F, P2=5 atm. Employing ideal gas model with constant specific heats at 80 degrees F determine the work and heat transfer per unit mass in Btu/ibm if n=1.3..
What is the most likely reason osha requires flooring : What is the most likely reason OSHA requires employers to protect flooring and handling areas in buildings against impregnation by ammonium nitrate and requires that the floors be constructed without open drains, traps
Obtain the forward kinematics equations for this robot : A 3 DOF robot manipulator is shown in Figure 1. a) Give a complete D-H parameter table. b) Give the three A-matrices that correspond to this robot. c) Obtain the forward kinematics equations for this robot. d) Solve the inverse kinematics problem. e)..
Obtain jacobian matrix using vector product method : A 3 DOF robot manipulator is shown in Figure 1. a) Give a complete D-H parameter table. b) Give the three A-matrices that correspond to this robot. c) Obtain the forward kinematics equations for this robot. d) Solve the inverse kinematics problem. e)..
What is the reason osha requires ammonium nitrate : What is the most likely reason OSHA requires ammonium nitrate to be segregated for sulfur or finely divided metals? Explain your answer.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The plank cde has a mass m15kg and is rest on a small pivot

the plank cde has a mass m15kg and is rest on a small pivot at d. a block a of mass 55 kg is resting on point c. a

  The turbines isentropic efficiency is 90 and the pump can

a steam rankine cycle operates between the pressures of 2500 psi in the boiler and 1 psi in the condenser. the turbine

  If the inlet axial mach number is 52 calculate the mean

a high pressure axial compressor for a jet engine rotates at 15000 rpm with an overall stagnation pressure ratio of

  Determie a if the quality of the mixture is initially at 50

a 2.0 cubic meter rigid tank contains a water-vapor mixture at 100 kpa. heat is transfered until the pressure reaches

  The tank and left on until the tank is observed to have

an insulated rigid tank contains 2.1 kg of water at 150 degress c initially. at this state 1.49 kg of the water is in

  Determine the normal and shear stress in directions

a steel pipe of 12-in. outer diameter is fabricated from 14in. thick plate by welding along a helix which forms an

  Determine the refrigeration load ql

Determine the refrigeration load QL and The COP of the refrigerator - If the isentropic efficiency of compressor is 0.8 calculate the actual work of the compressor.

  Determine a the time to make one pass across the surface

a peripheral milling operation is performed on the top surface of a rectangular part which is 400 mm long by 60 mm

  Select the proper equations to describe the flight of the

an unguided weapon is launched off a fighter aircraft flying at 500kts 844 fts straight and level at an altitude of

  The partition is now removed and the water expands to fill

a rigid tank is divided into two equal parts by a partition. one part of the tank contains 3.1 kg of compressed liquid

  Calculate the ratio of the turbulent h to the laminar

Water at 24 degree C flows at 0.8 m/s in a smooth, 1.5 cm I.D. tube that is kept at 27 degree C. The system is extremely clean and quiet, and the flow stays laminar until a noisy air compressor is turned on in the laboratory. Then it suddenly goes tu..

  What is the appropriate model tow velocity in ms a boat of

a boat of length 50 m is designed to cruise at 30 mph and is to be tested in a tow tank with a model of length 0.5 m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd