A small company is designing a new rigid commercial vehicle

Assignment Help Other Engineering
Reference no: EM13372317

A small company is designing a new rigid commercial vehicle. You are tasked with developing a spread sheet that allows the investigation of the road loads acting on a small rigid commercial vehicle due to aerodynamic and cornering forces.

Task 1

Using the supplied 3D model of the commercial vehicle available on Moodle and solidworks flowsimulation conduct a CFD analysis to determine the vehicles aerodynamic drag coefficient.

Task 2

Create a spread sheet in Excel that calculates the total individual wheel loads during cornering for lateral accelerations in the range 0 - 0.8g using roll centre analysis. The calculated wheel loads should consider the:

  • static load
  • aerodynamic load 
  • cornering loads

When designing the spread sheet you should consider that the coefficient of drag and the longitudinal velocity will need to be changeable.

Validate your spread sheet results via hand calculation

Report

Write a concise, professional report, at a minimum you should include:

  • A description of the methodology for both task 1 and 2 including all relevant assumptions
  • Validation of the spread sheet
  • Evaluation of the load transfer characteristics of the vehicle including the effects on vehicle handling

Submit your report and spread sheet electronically via Moodle. The 3D model and vehicle data sets are on Moodle at the top of the Vehicle Design page.

Reference no: EM13372317

Questions Cloud

X 420 610 625 500 400 550 650 480 565y 280 360 375 300 250 : x 420 610 625 500 400 550 650 480 565y 2.80 3.60 3.75 3.00 2.50 2.70 3.50 3.90 2.0 2.95 3.30calculate te covarience anf
Farm management case study from hillier and liebermans : farm management case study from hillier and liebermans introduction to operations researchthe ploughman family farm
Classify the following problems as to whether they are : classify the following problems as to whether they are pure-integer mixed-integer zero-one goal or nonlinear
One really good example of lean concepts and principles : one really good example of lean concepts and principles being applied in the service industry is southwest airlines. in
A small company is designing a new rigid commercial vehicle : a small company is designing a new rigid commercial vehicle. you are tasked with developing a spread sheet that allows
The figure below shows the geometrical stress concentration : the figure below shows the geometrical stress concentration factor k for a flat bar loaded in uniaxial tension. the
Citing specific evidence from machiavellis the prince : citing specific evidence from machiavellis the prince identify and briefly explain the qualities of the ideal political
Tabulate or graph the results analyze and discuss the : tabulate or graph the results analyze and discuss the results noting any interesting tures expectedunexpected relate to
Brinkers bicycle shop a special order decisionyour analysis : brinkers bicycle shop a special order decisionyour analysis should include the following steps to the extent logical

Reviews

Write a Review

 

Other Engineering Questions & Answers

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Determine the airflows and pressure drop

Determine the airflows and pressure drop in each of the branches and what are the flows and pressure drops in each of the branches?

  Analyse a proposed redesign of dehavilland vampire tail

Your task will be to analyse a proposed redesign of the de Havilland Vampire tail booms (not to be confused with a boom in your hand calculations) in an all metal configuration

  Sending water through the pipe network

Formulate a network optimization problem for transferring as much water as possible from the water depot to the fire district and how would you modify the above network and your model in part a so that you still only have flow balance and arc capa..

  Express the problem on a network by drawing nodes

Waste Management - Express the problem on a network by drawing nodes, arcs, determining node values, arc costs, arc capacities if any, such that no node has a capacity restriction associated with it and no node has a cost for using the node

  1 prepare a schematic diagram below of the major parts of

1. prepare a schematic diagram below of the major parts of the sem filament anode wehnelt condenser lens objective lens

  What are two key elements of a sis

CI-3110 - Give key reasons for the BP Texas City refinery explosion. What are recommendations to prevent further catastrophic event and what does SIS include

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

  Question 1a the use of satellites in rf communication

question 1a the use of satellites in rf communication system is a great deal fact in everyday life.i explain in detail

  Environmental engineeringquestion 4 the wastewater from a

environmental engineeringquestion 4 the wastewater from a restaurant contains organic matter with a theoretical oxygen

  How to write code for any particle shape using kk-3 system

how to write code for any particle shape using kk-3 system coding in grope

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd