A shell-and-tube heat exchanger must be designed to heat 25

Assignment Help Mechanical Engineering
Reference no: EM13631636

A shell-and-tube heat exchanger must be designed to heat 2.5 kg/s of water from 15 to 85 oC. The heating is to be accomplished by passing hot engine oil, which is available at 160 oC, through the shell side of the exchanger. The oil is known to provide an average convection coefficient oh ho = 400 W/m2 *k on the outside of the tubes. Ten tubes pass the water throughthe shell. Each tube is thin walled, of diamter D = 25mm, and makes eight passes through the shell. If the oil leaves the exchanger at 100 oC, what is its flow rate? How long must the tubes be to accomplish the desired heating?

Reference no: EM13631636

Questions Cloud

From the model in a you should have an equation for the : consider a space ship in a stationary orbit around a planet. the potential energy of the ship is u-kmr where kgm is
Gpa of scsu students is normally distributed with standard : gpa of scsu students is normally distributed with standard deviation 0.8. the average gpa of a random sample of 25
How much total recoil electron energy is deposited in the : a 2 mev gamma-ray photon is incident on a detector undergoes two sequential compton scatterings and then escapes. if
Construct a histogram and a percentage polygon construct a : one of the major measures of the quality of service provided by an organization is the speed with which the
A shell-and-tube heat exchanger must be designed to heat 25 : a shell-and-tube heat exchanger must be designed to heat 2.5 kgs of water from 15 to 85 oc. the heating is to be
What is the efficiency of the engine enter this as a : suppose a heat engine pulls 7.24times104 j of work from the hot reservoir and 1.35times104 j of that energy is used to
Suppose 250 people out a survey asking how many dogs and : suppose 250 people out a survey asking how many dogs and cats they own. the results are given in the following table
A researcher records the level of attention among 18 : a researcher records the level of attention among 18 students during an interactive and lecture portion of a single
The hull of a boat has a volume of 150 m3 and the total : the hull of a boat has a volume of 150 m3 and the total mass of the boat when empty is 8560 kg. determine how much load

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the following fluid and flow parameters using the

a device with an inlet cross-sectional area of 1 ft2 receives oxygen flowing at m0.2 with pt100 psia and tt1000 ordmr.

  Solid steel shaft d 20mm is subjected to a torque of 1200nm

solid steel shaft d 20mm is subjected to a torque of 1200nm. what size hollow circular steel shaft could be used to

  What is the packing density

What is the packing density

  Determine the following a the gas pressure lbfin2 when the

a gas is contained in a vertical piston-cylinder arrangement. the 50-lbm piston initially rests on the bottom stops.

  Derive from first principles an expression for the

derive from first principles an expression for the compressive buckling load on a simply supported beam of length l and

  A conveyor belt rises at a thirty degree angle its vertical

a conveyor belt rises at a thirty degree angle. its vertical hight measured from the ground is 20 ft sorry i cant seem

  The drain from the closed heater is trapped to the open

steam flow rate kgs for a reheat-regenerative steam power plant which is to produce 200 mw of electricity. the turbine

  Asume that x0 01 m and xdot0 0 the dsplacement xt is

consider the sysstem shown in figure 3-45 where m 2 kg b 4 nxm and k 20 nm. assume that x0 0.1 m and xdot0 0. the

  Determine the minimum power input

Air enters an adiabatic compressor at 0.1 kg/s, 100 kPa, 25 °C and exits at 700 kPa. (a) Draw a schematic of the system. Determine (b) the minimum power input (kW) and (c) the entropy generation rate (kW/K)

  The spring constant on car a is k 3mnm determine the

the 30-mg freight car a and 15-mg freight car b are moving toward each other with the velocities va 20 kmh to the right

  Air can be assumed to be an ideal gas with a

a well-insulated tank contains 1 mole of air at 2 mpa and 673 k. it is connected via a closed valve to an insulated

  To account for water losses in the cooling tower part of

the cooling water flow rate to the condensers of a big coal-fired power plant is 8460 kgs. the water enters the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd