User Account

All Pages

A pressured air supply is needed to generate a 1200-lb load

Assignment Help Mechanical Engineering
Reference no: EM13636394

A pressured air supply is needed to generate a 1200-lb load. The incoming air is 100 psig. The load must be raised at a stroke of 10" in 2 second. Assume the pneumatic design needs a rough efficiency with 10 psi pressure drop allowed. Please answer the following questions:

What is the minimum size of the piston diameter?
What is the port size of the control valve?

Reference no: EM13636394

Questions Cloud

Determine values of the specific volume of the saturated : at room temperature 25 c what pressure in both kpa and psi is required to liquefy propane c3h8? b determine values of
A soccer player kicks the ball toward a goal that is 286 m : 1 a duck has a mass of 2.0 kg. as the duck paddles a force of 0.06 n acts on it in a direction due east. in addition
The input conditions are 10c and 379 kpa what are the : a water heater operating under steady-flow conditions delivers 10 litersmin at 75 c and 370 kpa. the input conditions
Calculate the smallest increment of energy that can be : a calculate the smallest increment of energy that can be emitted orabsorbed at a wavelength of 10.8 mm?b what is the
A pressured air supply is needed to generate a 1200-lb load : a pressured air supply is needed to generate a 1200-lb load. the incoming air is 100 psig. the load must be raised at a
A wire 300 m long and 0450 mm2 in cross-sectional area has : a wire 3.00 m long and 0.450 mm2 in cross-sectional area has a resistance of 39 at 20degc. if its resistance increases
How whould you prepare a liter of carbonate buffer at a ph : how whould you prepare a liter of carbonate buffer at a ph of 10.10 you are provided with carbonic acid sodium hydrogen
A large boulder is ejected vertically upward from a volcano : a large boulder is ejected vertically upward from a volcano with an initial speed of 40.7 ms. air resistance may be
A saturated solution of strontium hydroxide is prepared : a saturated solution of strontium hydroxide is prepared andthe excess solid strontium hydroxide is allowed to settle.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the distance it travels before it starts

determine the time it takes for the ball to start rolling without slip and its speed when it does so. In addition, determine the distance it travels before it starts rolling without slip. Assume (mu)K = 0.10.

  A completely reversible air container provides 36000btuhr

a completely reversible air container provides 36000btuhr of cooling for a space maintained at 70 degrees fahrenheit

  Determine the average value of the material

How often would the sample have to be taken - If the objective was to determine the average value of the material in the bunker, how could this be done by making one measurement?

  The cut-off ratio for the cycle is 2 determine the

an air-standard diesel cycle operates with a compression ratio of 18. at the beginning of the compression process the

  A 1 kg block of copper at 350degc is quenched in a 10 kg

a 1 kg block of copper at 350degc is quenched in a 10 kg oil bath initially at ambient temperature of 20degc.

  It is known that the compressor consumes 12kw of

r-134a enters the condenser of a refrigerator at 800kpa and 50oc at a rate of 0.018kgs and leaves at 800kpa as a

  Calculate the increase in entropy which occurs when the

a rigid container is divided into two compartments of equal volume by a partition. one compartment contains 1 mole of

  Suppose we load this cart with a crate of mass 104 kg where

you are given a four-wheeled cart of mass 15 kg where the distance between a wheel and its nearest neighbors is 2 m.

  5 kgm of water is at 15 c and is contained in a vertical

5 kgm of water is at 15 c and is contained in a vertical cylinder by a frictionless piston of a mass such that the

  A brayton cycle gas turbine delivers power to an electric

a brayton cycle gas turbine delivers power to an electric generator at 150 mw. the minimum nbsptemperature in the cycle

  An ideal diesel cycle with air as the working fluid has a

an ideal diesel cycle with air as the working fluid has a compression ratio of 20 and a cutoff ratio 2.1. at the

  What is the repair rate

If the unit can perform its function either in State 1 or 2, find the steady-state availability A for the device.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd