A lunar transfer vehicle masses

Assignment Help Mechanical Engineering
Reference no: EM13703836

A lunar transfer vehicle masses 50 tonnes (metric tons, or 1000 kg) fully fuelled, has a dry mass of 15 tonnes, which includes 5 tonnes of cargo. Assume lox/hydrogen engines with Isp = 445 seconds are used. How much Delta V does this vehicle provide?

Reference no: EM13703836

Questions Cloud

What statistical outcomes would distinguish a better player : As a game, slide a matchbook across a table, trying to make it stop at some predefined point on each attempt. Measure the distance from the starting point to the stopping point. Repeat this 10, 20, through 50 times. Plot the frequency distribution fr..
And open center spool valve : And open center spool valve
What vertical distance do the two stones miss : Two girls standing 20 m apart are both throwing balls towards a tree to knock down a shoe hanging 7 m up in a tree that is directly between them. Girl A is 7 m from the tree while Girl B is 13 m from the tree.
Principal stresses and maximum principle shear stress : The cantilevered bar in the figure has a circular cross section and is subject to bending and torsion. The normal stress due to bending in x=28 kpsi and the shear stress due to torsion is xz=15.3 kpsi. The change in diameter introduces a stress conce..
A lunar transfer vehicle masses : A lunar transfer vehicle masses 50 tonnes (metric tons, or 1000 kg) fully fuelled, has a dry mass of 15 tonnes, which includes 5 tonnes of cargo. Assume lox/hydrogen engines with Isp = 445 seconds are used. How much Delta V does this vehicle provide?
Calculated from the manufacturers performance tables : Compare the ideal COP of R-134a and R-22 at an evaporating temperature of 40 F and 20 F superheat and condensing temperature of 120 F with 15 F sub cooling with the actual compressor COPs calculated from the manufacturer's performance tables.
Find the mass of the gas remaining in the cylinder : An ideal gas contained in a cylinder with a volume of 500m3 is at a pressure of 400Kpa and a temperature of 70 ?C . Pressure in the cylinder is dropped to 200KPa by releasing some gas. If the expansion process of the cylinder is isentropic, find the ..
Find the change in internal energy of the system : A fluid with a specific volume of 0.2m3 /Kg at 500KPa pressure enters a system with 8 m/s velocity. Heat losses in the system are found out to be 50 KJ/Kg of fluid supplied. The leaving pressure of the fluid is 100Kpa with a specific volume of 0.1m3 ..
A rigid tank initially contains a mixture of liquid water : A rigid tank initially contains a mixture of liquid water and water vapor at a pressure of 14.7 psia. Determine the proportions by volume of liquid and vapor necessary to make the mixture pass through the critical point when heated

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the volume of h2 produced at 1 atm and 298k

consider an electrolytic cell for producing hydrogen and oxygen mi h2so4 0.5mmii where mi and mii are carbon rods. a

  Calculate the yield stress of the material

Calculate the yield stress of the material and the force required to produce yield - determine the bulk modulus of the material.

  What is the exit air speed

Air enters a machine at 373 C with a speed of 200 m/s and leaves it at 293 C. If the flow is adiabatic, and the work output by machine is 105 Nm /kg, what is the exit air speed? What is the exit air speed when machine is delivering no work?

  A woman with wieght 637n lies on a bed of nails the bed has

a woman with wieght 637n lies on a bed of nails. the bed has a weight of 735n and a lenght of 1.72m. the bed is held up

  The nitrogen is compressed to frac12 of the initial volume

two kg of nitrogen at 40degc and 200 kpa are contained in a frictionless piston-cylinder device. the nitrogen is

  A fluid film of 02 mm thick separates the cube and the

a 100 n cube slides down an inclined plane of 30 degrees with the horizontal. a fluid film of 0.2 mm thick separates

  Calculate the contact forces at a and b

the 50-kg homogeneous smooth sphere rest on the 30 degree incline A and bears against the smooth vertical wall B. calculate the contact forces at A and B.

  Compute the work done for this process

(1) I shte cooling process polytropic? If so, what is the value of n? (2) Find the final state pressure. (3) Compute the work done for this process considering the water as a closed system.

  Which of these two processes will produce the largest amount

which of these two processes will produce the largest amount of work? (You must provide a full explanation for your choice).

  Calculate the required heat transfer to or from the reactor

it is highly desirable to make benzene from ethane from shale gas in a continious vapor-phase reaction3c2h6 --gt c6h6

  A pison-cylinder contains 08 kg of steam of 300oc and 1

a pison-cylinder contains 0.8 kg of steam of 300oc and 1 mpa. the steam is cooled at constant pressure until one-half

  Determine the first law thermal efficiency and compare it

in a rankine cycle steam leaves the boiler at 400 celsius and 5mpa. the condenser pressure is 0.01mpa. the water

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd