Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
In a processing plant, a chemical tower has a liquid which is vaporized. However, if the vapor in the tower reaches 150°C, an alarm needs to be generated so that safe shutdown of that system of the plant may be initiated. An RTD will be used to measure the temperature of the vapor. The RTD will generally operate between 80° to 175°C and has a resistance of 220? at 20°C. The fractional change in resistance per 1°C is 0.0040. The dissipation constant is 25mW/°C. Design a circuit to activate an LED alarm when the temperature reaches 150 °C. The error should not exceed +/-1°C. Use a single supply voltage.
Design a microstrip transmission line with Z0 =100 ohm that will be etched onto a sielectric substrate with er = 3 and a thickness of 4 mm. what should be the width of the microstrip line
A flat sheet of paper of area 0.150 m2 is oriented so that the normal to the sheet is at an angle of 65° to a uniform electric field of magnitude 29 N/C. (a) Find the magnitude of the electric flux through the sheet.
Determine the power consumed by the two elements, determine the current leaving the source, determine the power factor and specify leading or lagging. Also, determine the size of the capacitor (in kVARs) needed to bring the power factor to 1
Find the input torque to the generator.If armature current and field current are kept constant, find the new value of the terminal voltage if the power factor is changed to 0.7 lagging.
An FM signal being transmitted is represented by eFM(t) = 50Sin((2)(95.1)(106)t+2Sin((2)(10)(103)t)). If the antenna impedance is 75 , determine: (a) total power in FM signal and (b) FM modulation index.
Design an ac-dc voltage converter based on half-wave rectification and filtering. The requirements are: 1. Choose the values of the load resistor R and the capacitor C so that the converter will have a ripple factor of 10%
1. What is the purpose of core in hollow solder wire 2. What is tinning, and why is it important 3. Why is safety so important when soldering 4. Why has lead-free solder replaced lead-based solder. Be sure to properly cite any sources of information.
Consider the following MATLAB code: a = 0:(1/9000):4; % vector of time samples b = 100*a; % instantaneous frequency x = sin(4*pi*b.*a); (a) How many samples are in vector a, b, and x, respectively
Design a 3-bit counter using D flip-flops to cycle through the following sequence: 010, 101, 110,001. Make sure the counter is self-starting.
Suppose a DC power source with a voltage of 50 volts is connected to a 10-ohm load. How much power will this load dissipate. Now suppose the same 10 ? load is connected to a sinusoidal AC power source with a peak voltage of 50 volts.
1. What is the difference between discrete system and digital system. 2. What is "baseband modulation"? What types of baseband modulation are there. 3. How does time division multiplexing work? What factors affect how many channels you can transmit.
A solid sphere with a radius of 75 mm rolls (without slipping) down an inclined plane that is 5 m long. What is the angular velocity of the sphere at the bottom of the plane if it requires 10 seconds for it to reach the bottom
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd