A 100 lb door has a weight of 100 lbs and a center

Assignment Help Civil Engineering
Reference no: EM13549268

A 100 lb door has a weight of 100 lbs and a center of gravity at point g. determine the resultant force at points A and B. Point B resists forces in the X and Y directions. Point A resists forces in the X, Y and Z directions. The bottom horizontal edge of the door lies on the Y axis and the left vertical edge lies on the Z axis. The tho hinges lie on the Z axis on the left of the door. Point A is 18" from the floor on Z axis , Point B lies 66" from the floor on Z axis . Point G lies 42" from the floor and 18" to the right of the Z axis.

Reference no: EM13549268

Questions Cloud

Determine the final temperature of the steam and the amount : An insulated piston cylinder device initially contains 0.01m^3 of steam at 473 K the force on the piston is such that it maintains a constant pressure of 400kpa Inside . A valve is now opened and steam at 1Mpa at 473 K is allowed to enter the cylinde..
Determine the system curve for the pump system : Water is pumped from the tank 1 to tank 2 as shown below. The suction side pipe is nominal 4, schedule 40, 24 ft long, f = 0.018, and the discharge pipe is nominal 3 ½ , schedule 40, f = 0.019, and is 400 ft long
Properties must be the same throughout the system : The interaction that occurs between a system and its surroundings as the system executes a process, which is the result of the system being at a temperature different from that of the surroundings.
Determine the vertical deflection and the slope at the end : Determine the vertical deflection and the slope at the end of A of the bracket. Assume that the bracket is fixed supported at its base, and neglect the axial deformation of segment AB. EI is constant.
A 100 lb door has a weight of 100 lbs and a center : A 100 lb door has a weight of 100 lbs and a center of gravity at point g. determine the resultant force at points A and B. Point B resists forces in the X and Y directions. Point A resists forces in the X, Y and Z directions. The bottom horizontal ed..
Expresses the relationship for the change in entropy in a : Steam at 10 MPA, 600 C, enters a well insulated turbine operating at steady state and exits at 0.1 bar and a quality of 92%. The volumetric flow rate at the inlet is 0.36 m^3/s. Assuming the kinetic and potential energy effects to be negligible, dete..
Discuss the role that you believe your surety would play in : The New Jersey Surety Association, in various documented publications discusses the Surety’s relationship with their clients, the best ways to better know your Surety and a brief overview of why the Construction Business can fail.
Each of the three partners realizes that in order for the : Hardly Able Contracting Co., Inc., Contractors & Engineers, has been in business for twenty five years and has been progressively expanding since the firm’s inception
Helium gas is compressed is entropically from 1 bar and 25 c : Helium gas is compressed isentropically from 1 bar and 25 C to a pressure of 10 bar. The temperature of Helium after the compression is A) 25 C B) 63 C C) 250 C D) 384 C E) 476 C

Reviews

Write a Review

Civil Engineering Questions & Answers

  Is the correct difference in elevation between a and b

A level is set up midway between two wood stakes that are about 300 feet apart. The rod reading on Stake A is 9.65 ft and the reading on stake B is 4.23 ft. The level is then set up 6 feet in front of stake B.

  Find si value of absolute pressure corresponding to vaccum

What is the SI value of absolute pressure corresponding to a vacuum pressure of -10 inches of water. Assume the location is Moscow, Idaho. What is the SI value of gage pressure corresponding to a pressure 14 psia. Assume the location is Denver, Colo..

  Calculate size of the critical radius and number of atoms

For maximum undercooling, calculate the size of the critical radius and the number of atoms in the critical nucleus when solid copper forms by nucleation.

  How to estimate for the loaded machines on level ground

Stripping overburden in the Illinois coal belt, the Dusty Coal Company uses 270-horsepower, track-type tractors (with direct-drive transmissions) and drawn scrapers.

  Determine the aeration period and f by m ratio

Two activated sludge aeration tanks in Podunk, MO are operated in series. Each tank has the follwing dimensions: 7.0 m wide x 28.0 m long x 3.5 m effective liquid depth.

  Estimate the community water requirements in 2010 assuming

A community had a population of 200,000 in 1995 and it is expected that this will increase to 260,000 by 2010. The water treatment capacity in 1995 was 165 ML/day. A survey showed that the average per capita water use rate was 700 L/(person.day). Est..

  Calculate the speed of the water relative to the hydrofoil

A speedboat on hydrofoils is moving at 20 m/s in a freshwater lake. Each hydrofoil is 3 m below the surface. Assuming, as an apporximation, frictionless, incompressible flow, find the stagnation pressure(gage) at the front of each hydrofoil.

  Determine what fair amount contractor should receive

Determine what fair amount she should receive if she decides she want to be paid: a. In 2 equal installments - one immediately (at T=0) and one at the end of month 36.

  Calculate what real rate of return will the investor receive

A man bought a 5% tax-free municipal bond .It cost $1000 and will pay $50 interest each year for 20 years.At maturity the bond returns the original $1000 .If there is 2% annual inflation

  Estimate the velocity with which you would contact

Estimate the velocity with which you would contact the ground if you jumped from an airplane at an altitude of 500ft and a) air resistance is negligible, b) air resistance is important, but you forgot your parachute, and c) you use a 25-ft-diameter p..

  What is the tce concentration in mg per cubic meter

The concentration of trichloroethelyne (TCE) in an air sample near a hazardous waste landfill is 34 ppm, the ambient air temperature is 31 degrees C, and the atmospheric pressure is 0.94 atm. What is the TCE concentration in mg/m^3

  Create time vector going from 0 to 19 in 1 second increments

Write a MATLAB program that loads the sensor_new.dat file. The sensor readings were actually taken every second over a period from 0 to 19 seconds. Create a time vector going from 0 to 19 in 1 second increments.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd